Strafford County, New Hampshire Map with Towns and Land Area

How to use this map

The map opens on the Divisions view with all 13 of Strafford County’s municipalities drawn straight from Census boundary files. Click any one to pin it and read its figures: land area in square kilometres, 2020 population and the density that falls out of those two. The tabs above the map change what the shading means. Divisions gives each unit its own colour so you can tell neighbours apart at a glance. Land area shades by size. Satellite drops one metre aerial imagery under the boundaries. Blank outline strips the fill away for printing or tracing.

The figure people misread is land area. Census land area excludes water, so a municipality with a lake or a river frontage looks smaller in the table than it does on the map. New Durham is the clearest case here: its boundary encloses 113.32 square kilometres but only 106.73 of that is land, leaving 6.59 as water. If you are measuring something that sits on the ground, use the land figure. If you are measuring something that follows the boundary, use the polygon.

What this county is made of

Strafford County holds 10 towns, 3 citys. Strafford is the largest by land area at 126.97 square kilometres and Rollinsford the smallest at 18.88, which makes the largest roughly 6.7 times the size of the smallest. The median sits at 69.24 square kilometres, so the spread is wide but most units cluster nearer the middle than the extremes.

Dover is the county seat, which is the New England term for what the rest of the country calls a county seat. Dover is the largest by population at 32,741, about 25 per cent of the county total. Dover is the densest at 472.9 people per square kilometre and New Durham the emptiest at 25.2, a ratio of about 19 to one. Middleton has 1,823 people.

Across the whole county the density is 137.5 people per square kilometre. That is the number to hold on to, because it explains the shape of the map: a few dense nodes and a long tail of thinly settled ground, with the average describing almost none of the individual units.

Where the data comes from

Boundaries come from the Census Bureau TIGERweb county subdivision layer, which is the authoritative source for municipal geography in New Hampshire. Land area is the Census land measurement, which excludes inland water. Population is the 2020 Decennial Census count for each municipality.

The sources are joined on municipality name, and that join is worth checking rather than trusting. The 13 land areas sum to 951.77 square kilometres against a published county land area of 951.77, which agrees to the hundredth. The 13 with published figures sum to 130,889, which is the published county total to the person.

Aerial imagery, and how it is fitted to the map

The Satellite tab pulls one metre aerial imagery from the USGS National Map. One metre means each pixel covers roughly a square metre of ground, so at full zoom you can pick out individual buildings, field boundaries and the line of a farm track. That resolution matters at this scale. The national and state maps on this site use a NASA composite at five hundred metres per pixel, which is fine for showing where New Hampshire sits in the country and useless for showing where a municipal line runs.

The boundaries are drawn in an Albers equal area projection fitted to this county, with standard parallels set inside its own latitude range. Equal area matters here because the map is shaded by area: if the projection distorted area, the shading would be lying. The imagery arrives in Web Mercator and is reprojected to match.

A check you can repeat on paper

Take Dover. Its land area is 69.24 square kilometres and its 2020 population is 32,741. Divide 32,741 by 69.24 and you get 472.86 people per square kilometre, which is what the panel shows rounded to 472.9.

Now check it against the county. Dover holds 25.0 per cent of the 130,889 people on 7.3 per cent of the 951.77 square kilometres. That gap between population share and land share is the whole story of the map in one comparison.

Mistakes that catch people out

Reading polygon area as land area. The map draws boundaries, and boundaries include water. This county encloses 989.09 square kilometres of polygon against 951.77 of land, so 37.32 is water, about 3.8 per cent.

Assuming a city is bigger than a town. In New Hampshire those words describe charter type, not size. Rollinsford town is the smallest unit here at 18.88 square kilometres.

Expecting the average to describe a unit. At 137.5 per square kilometre the county average sits between New Durham at 25.2 and Dover at 472.9, and matches neither.

Assuming municipal lines follow roads or rivers. Many were surveyed as charter grants or survey townships long before the roads existed. The straight lines on this map are the original survey, not modern infrastructure.

Related Calculators and Reference

• New Hampshire County Map, for all 10 counties and where Strafford sits among them
• United States Map, for the national view and how New Hampshire compares
• Massachusetts County Map, for the same treatment applied to another New England state
• US Census Bureau Geography, the source for boundaries, land area and population